Beko Dishwasher Problems And Troubleshooting

Beko dishwashers have earned high ratings and were among the top five dishwashers in 2019. They feature smart innovations like new rail systems with ball bearings, inner illumination, and outstanding A+++ energy efficiency ratings. These appliances are designed for effective drying and resource savings, while GlassShield technology ensures your glassware's protection by stabilizing water levels.

Yet, even the most exceptional technology can encounter issues. Explore a variety of Beko dishwasher problems and troubleshooting solutions here. If you face persistent problems, consider seeking professional Beko dishwasher repair in London to keep your appliance performing at its best.

Operating Teething Troubles

A Beko dishwasher not working can be due to a range of Beko dishwasher faults. These include issues with the:

• Drain
• Water fill
• Heating and detergent dispenser
• Water pump
• Water inlet and draining

You can easily check all of the mentioned factors during an initiated test cycle for your Beko dishwasher in London. This test cycle is designed to halt at the first sign of a fault, displaying the corresponding error code. It systematically assesses each function, helping to pinpoint the source of any malfunction.

If you encounter any concerns or issues during this process, don't hesitate to reach out to your trusted Beko dishwasher repair experts in London. They have the knowledge and experience to swiftly diagnose and resolve any problems, ensuring your dishwasher operates smoothly once more. Your convenience is our priority, and we're here to assist you with any dishwasher-related issues you may encounter.

Fault Codes

Beko dishwasher error codes are displayed as digital codes in an LED or LCD panel or display on the door. Beko dishwasher common faults are as follows:

• H2 – dishwasher turbidity sensor error – this is the pump sensor that detects the detergent is there
• H3 – diverter valve position error – this controls the water flow to the spray arms
• H4 – NTC error – the temperature sensor is unable to be read
• H5 – Uninterruptable water inlet error – malfunction of the water-inlet valve or the T7 triac on the electronic board
• H6 – water inlet fault – the dishwasher is unable to fill with no water detected
• H7 – heating fault – the correct temperature can’t be reached and the heater is not detected

Error Lights

• No lights – this indicated there isn’t any power or no faults are detected
• 1st light lit – dishwasher not filling with sufficient amount of water
• 2nd light lit – inlet valve or water sensor error
• 3rd light lit – water temperature sensor error
• 1st and 2nd lights lit – heating element fault

All of these fault codes only offer an indication of where the issue lies. You’ll need a technician with diagnostic skills to find the specific fault and fix it.

Water-Filling Hitches

A Beko dishwasher not filling could indicate a problem with the water pressure. This needs to be between 0.3 and 10 bar. The issue could be related to a kinked or damaged inlet hose and even drainage difficulties. If there’s no water at all this could be related to the water supply.

A defective float switch means that it won’t be able to fall back down as the water is drained to monitor the water level. This, in turn, will stop the inlet valve from opening and letting water into the appliance.

Dishwasher Salt Issues

Beko dishwasher salt problems can occur if you’ve been using table salt. This isn’t recommended as the dishwasher salt is a particular grade of granulated, crystalline sodium chloride that regenerates the water softener. The large granules allow the salt to dissolve slowly and not block the softener unit.

The addition of dishwasher salt can prevent watermarks and spots by reducing limescale. Bear in mind that insufficient water in the dishwasher can also cause poor cleaning.

Drainage Difficulties

A Beko dishwasher not draining may be due to the position of the drain hose connected to the appliance. It should be between 50cm and 100cm above the floor to ensure it works correctly. Blocked filters can also be an issue and may need to be cleaned or replaced. An engineer will swiftly find the cause and be able to remedy it.

Cleaning Concerns

Another Beko dishwasher troubleshooting area is when your Beko dishwasher is not washing properly. You’ll need to ensure that the wash program is suitable for the level of soiling on your dishes. And make sure you’re loading the appliance correctly, and not overloading.

Additional factors that can affect the wash results include blocked filters, nozzles, and issues with the spray arms.

Drying Dilemmas

Your Beko dishwasher may not be drying the dishes properly due to problems with the vent not opening. The vent allows the hot air generated during the rinse cycle to escape. If this can’t happen moisture will remain on the dishes.

Dryer fan malfunctions can be caused by food remnants and debris blocking the airflow. Or the fan motor may have burned out and will need replacing. Heating elements, terminals, and connectors can corrode and will need to be expertly cleaned or replaced. And defective thermostats will be unable to regulate the drying cycle temperature.

When You Need the Professionals

When you book appliance repairs in London for your Beko dishwasher, our London repair experts ensure your peace of mind. With a dedicated focus on customer satisfaction, we back our repairs with a solid six-month guarantee.

Our highly trained specialists arrive fully equipped with the latest tools and perform their work under comprehensive insurance coverage for your protection. You can count on us to accommodate your schedule with short notice or even same-day service. Rest assured, your appliance will be swiftly restored to its optimal functionality, just like new. Your convenience is our priority, and we're here to make your dishwasher repair experience as smooth and hassle-free as possible.